Products

Wet scrubber is used for air pollution control. The principle of wet scrubbers is that the dust laden air or gas is brought in contact with fine droplets of scrubbing liquid which is usually water, in a high turbulent zone which is created in a ventury. Due to high velocity and high turbulence the fine dust in the air or gas gets mixed with the scrubber liquid and the air or gas becomes dust free.

Direct fired hot air generators are used to heat the air for processes which can allow mixing of products of combustion with the products which come in contact with hot air. Direct Fired Hot Air GeneratorsView Large

Mixing equipment is typically engineered with blades and motors precisely designed to carry out particular mixing process. Different processing methods include blending dry powders, mixing high-viscosity pastes, homogenizing, emulsifying, agglomeration, or reducing particle size. Industrial mixing may be performed at a wide range of different processing temperatures and operating pressures. Mixer selection is decided by various factors like viscosity, nature of feed, heat sensitivity of feed, nature of final product, etc. We offer industrial mixers of various types for powder processing are, Ribbon Blender Double Cone Blender Cone Screw Mixers Paddle Mixer Conical Blender

Agitated Thin Film Dryers are used to dry liquid solutions or slurries into flakes or powder. Agitated thin film dryer consists of a jacketed vertical shell having an agitator shaft mounted with multiple blades on it. Either steam or hot oil is passed through the jacket of the shell thereby heating the internal surface of the shell to required tem perature. The liquid feed is introduced at the top and the dry product is discharged at the bottom.

Forced Circulation Evaporators are specially designed for liquids that tend to scale, foul, highly viscous and crystallize depending upon the final concentration of the product. Feed is re-circulated in the shell and tube heat exchanger by pumping, heated under pressure to prevent boiling, and then flashed in the vapor liquid separator, where the absolute pressure is slightly less than in the heat exchanger, to obtain the required vaporization

Evaporators are used to increase the solid content in the liquids containing low solids, by evaporationg water or solvent from the liquid Evaporators basically consist of shell and tube heat exchanger columns called as calandrias. The product to be concentrated is passed through the tubes and the heating media, usually steam, is passed through the shell. The calandria tube side is under vacuum causing the liquid boiling at lower temperature, Thus making the operation economical and safe for heat sensitive products. Following are the types of evaporators depending upon the feed circulation configuration.

Agitated Thin Film Dryers are used to dry liquid solutions or slurries into flakes or powder. Agitated thin film dryer consists of a jacketed vertical shell having an agitator shaft mounted with multiple blades on it. Either steam or hot oil is passed through the jacket of the shell thereby heating the internal surface of the shell to required tem perature. The liquid feed is introduced at the top and the dry product is discharged at the bottom. Agitated Thin Film DryersView Large

Paddle dryers are conduction dryers used for drying of sludge, paste or wet powder. Paddle dryer consists of horizontal container with single or double shafts mounted with hollow paddles. The paddles are specially designed to make them self-cleaning. The container is provided with jacket. Steam or hot oil is passed through the container jacket as well as the paddles so that all the internal surfaces are heated up. Paddle DryersView Large

Continuous fluid bed dryers are used for drying of free flowing wet products which require longer drying time. Continuous fluid bed dryer consists of horizontal chambers partitioned by a custom built perforated sheets. The product to be dried is fed on top of this perforated sheet and the hot air enters from the bottom of the perforated sheet. The hot air causes the fluidisation of the product causing mild agitation. During this time the product gets dried. To assist fluidisation or movement of difficult to handle products the fluid bed chambers are mounted on springs and fitted with vibratory motors and these are called vibratory fluid bed dryers. The ancillaries like air heating system, fans, cyclone separators, bag filters and scrubbers are the same as are used in other type of dryers. Continuous Fluid Bed DryersView Large

Rotary Tube Bundle Dryer is one of the most effective and energy dryers. Our design is at minimum temperature drying for superior quality output and low stream consumption. The wet feed material is fed into rotating drum, which consists of tube bundle inside it. The tubes are heated by means of steam/rhermic oil flowing inside. Tube and bundle rotates at slow speed in a stationery housing in which material passes over these tubes and material gets dried by heat of conduction.

Rotary dryers are used for drying wet powders or wet cakes which require long time to dry. Rotary dryer consists of a hollow drum fitted with staggered louvres internally. The wet product is fed at one end of the rotating drum. The hot air comes in contact with the product and by the time the product travels up to the other end of the drum, it gets dried. Rotary DryersView Large

Agitated flash dryers are used for drying of wet powders, cakes or even pastes and convert into fine powder. The difference between flash dryer and agitated flash dryer is that in an agitated flash dryer there is a pulverising effect that gives the final dried product as fine powder having particle size smaller than the feed. Agitated Flash Dryers View Large